FUJI错误代码查询.pdf - 第1192页

body sized. ------------------------------ Code: 1CA??00C Display: 1CA??00C Used by: Cause: If "??" equals 28 this signifies that the body has failed to be detected. If "??" equal A0 then the body edg…

equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then not enough leads were detected.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 15, or 18 this indicates that the necessary number of corners

(more than two) were not found for determining the part position. Make sure that the nozzle is not bent

and that the part is being properly picked from the feeder. If "??" equals 14 or 28 then make sure that the

part data is correct. In particular make sure that the P_pattern setting is correct. If "??" equals 16 or 17

then check the part data. If the part data is satisfactory then decrease the Body_ and Body_y settings in

Tolerance information. If "??" equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then a minimum of two

leads must be detected.Check the number of leads set, and "Result".

------------------------------

Code: 1CA??008

Display: 1CA??008

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 10, 15, or 18 this signifies that the X-dimension of the part has exceeded the permissible range. If

"??" equals 14 or 28 then a lead was found in a location where no lead was expected. If "??" equals 16 or

17 then the inspected leads were larger than specified. If "??" equal 7B, 7C, 96, 97, 98, 99, F0 or FE then

invalid lead width value.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 10, 15, or 18 then the part size is wrong. Make sure that the part

data is correct. If "??" equals 14 or 28 then verify that the lead arrangement information is correct. Also,

be sure that the correct part is being used. If "??" equals 16 or 17 then check the part data. If the part

data is satisfactory then increase the Body_x and Body_y settings in Tolerance information. If "??" equal

7B, 7C, 96, 97, 98, 99, F0 or FE then the lead width input is 0 or less. Check the lead width.

------------------------------

Code: 1CA??009

Display: 1CA??009

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 10, 15, or 18 this signifies that the Y-dimension of the part has exceeded the permissible range.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 10, 15, or 18 then the part size is wrong. Make sure that the part

data is correct.

------------------------------

Code: 1CA??00A

Display: 1CA??00A

Used by:

Cause: If "??" equals 0D or 18 then the supply orientation of the part is incorrect. If "??" equal 64, 78, 79,

7A, 7B, 7C, 96, 97, 98, 99 or F0 then invalid lead length value.

Remedy: If "??" equals 0D the error has occurred as a result of the direction test that is utilized when

tantalum sprague components are processed. If "??" equals 18 the error has occurred as a result of the

direction test that is utilized when trimmer resistor components are processed. Set the correct supply

orientation. If "??" equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then the lead length input is 0 or

less. Check the lead length.

------------------------------

Code: 1CA??00B

Display: 1CA??00B

Used by:

Cause: If "??" equals 0A, 14 or 28 this signifies that positioning could not be determined correctly

because the image was oscillating. If "??" equal A0 then the part angle is being obtained incorrectly. If "??"

equal 64, 78, 79, 7A, 7B, or 7C then the element size is larger than the body size.

Remedy: If "??" equals 0A, 14 or 28 then this error occurs on the FCP5. Carry out readjustment of the

index servo. If "??" equal A0 then check to see if burrs on the part edges, or dust on the background is

causing an image problem. If "??" equal 64, 78, 79, 7A, 7B, or 7C then check the element size and the

第 1191 页

body sized.

------------------------------

Code: 1CA??00C

Display: 1CA??00C

Used by:

Cause: If "??" equals 28 this signifies that the body has failed to be detected. If "??" equal A0 then the

body edge cannot be detected. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then invalid lead pitch value.

Remedy: If "??" equals 28 then check the dimensions of the part. If "??" equal A0 then check for errors in

the part data's "part size" setting, and in the element_data detection position. If "??" equal 64, 78, 79, 7A,

7B, 7C or F0 then the lead pitch is smaller than the lead width.Check the lead pitch and the lead width.

------------------------------

Code: 1CA??00D

Display: 1CA??00D

Used by:

Cause: If "??" equals 28 this signifies that there were no body detection points. If "??" equal A0 then

mismatch between the part size and the part data. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then there are

overlapping elements.

Remedy: If "??" equals 28 then the results of calculating the body detection points using the body data

prevented the body from being detected because the leads were concealed by the body. If "??" equal A0

then specify the correct part size in part data. When there is a large size difference from part to part,

specify a large tolerance value. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then check the element data, and

ensure none of the elements are overlapping.

------------------------------

Code: 1CA??010

Display: 1CA??010

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 78,

79, 96, 99, 9B or 9E this signifies that the positioning phase could not be determined. If "??" equal A0

then coarse positioning is not possible. If "??" equal F0, F1 or F2 then search failed.

Remedy: If "??" equals 64, 78, or 79 this indicates that there is a problem with the brightness of the

image. Make sure that there is no dirt or dust reflected in the background. If "??" equals 96,99, 9B or 9E

then verify that the part and mechanical chuck do not lie outside of the camera field of vision. Also make

sure that there is not a problem with the brightness of the image and that there are no contaminants

reflected in the background.

If "??" equal A0 then cCheck for the following:

o Part or mechanical chuck protruding from the camera's field of vision.

o Image brightness problem.

o Image problem caused by dust, etc., on the part background.

When a nozzle is being used, the size of the nozzle's reflective disk should be at least 1.7 times the part

size.

If "??" equal F0, F1 or F2 then check for errors in the part data. Create a model to reduce the size of the

circumscribed square outline for the entire model.

------------------------------

Code: 1CA??011

Display: 1CA??011

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 1E, 64,

78, 79, AC, or FE then boundary detection could not begin because the nozzle was bent. The image lies

outside the scan area. If "??" equals 7C, 82, 83, 98, 9D or B4 this indicates that the leads could not be

acquired from the body and background. If "??" equals 8C, E6, E7 or E9 there are too few leads described

in part data. If "??" equal F0, F1 or F2 then model size exceeds the tolerance range.

第 1192 页

Remedy: If "??" equals 1E, 64, 78, 79, AC or FE then either the nozzle center of rotation does not conform

with the image of the nozzle or the image lies outside of the scan area. Make sure the nozzle is not bent.

Or in the case that the image lies outside of the camera field of vision, enlarge the scan area. If "??" equals

7C, 82, 83, 98, 9D or B4 this signifies that the body could not be distinguishedor separated from the

leads. Input the Lead_brightness in part data. If "??" equals 8C, E6, E7 or E9 there are too ew leads

described in part data and the positioning phase could not be carried out. Correct the part data. If "??"

equal F0, F1 or F2 then check the model size. Create a model to reduce the size of the circumscribed

square outline for the entire model.

------------------------------

Code: 1CA??012

Display: 1CA??012

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 1E, 64,

78, 79, AC, or FE this signifies that the image of the part that has been found is smaller than thesize of

the nozzle. If "??" equals 8C, E6, E7, or E9 then the part is too big.

No license key is required when ?? = F1 or F2.

Remedy: If "??" equals 1E, 64, 78, 79, AC, or FE then either the image of the part that has been found is

smaller than the size of the nozzle or the image lies outside of the field of vision. Make sure the correct

nozzle has been specified. Or in the case that the image lies outside of the camera field of vision, enlarge

the scan area. If "??" equals 8C, E6, E7, or E9 then a valid field of vision cannot be acquired since the

part size is too big.

When ?? = F1 or F2, confirm that there is a license key, or that the license key is operating properly.

------------------------------

Code: 1CA??013

Display: 1CA??013

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 82, 83, 8D, 8E, 98, 9D or B4 this indicates that the leads could not be acquired from the body and

background. If "??" equals 8C, E6, E7, or E9 then no leads exist.

Remedy: If "??" equals 7B, 7C, 82, 83, 8D, 8E, 98, 9D or B4 this signifies that the body could not be

distinguished or separated from the leads. Input the Lead_brightness in part data. If "??" equals 8C, E6,

E7, or E9 this indicates that not a single lead was reflected. Make sure that the image has been acquired

properly.

------------------------------

Code: 1CA??014

Display: 1CA??014

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 82, 83, 98 or B4 this signifies that the threshold value request was improper. If "??" equals 8C, E6 or

E7 then the body size has not been input in part data. If "??" equal 8D or 8E then the body size is

incorrect.

Remedy: If "??" equals 7B, 7C, 82, 83, 98, or B4 this is an internal error that normally does not occur. If

"??" equals 8C, E6, E7 or E9 then input the correct data in part data. If "??" equal 8D or 8E then the

specified body size exceeds the tolerance value registered in part data. Check the body size.

------------------------------

Code: 1CA??015

Display: 1CA??015

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 7B, 7C,

98 or b4 then part search area is incorrect.

Remedy: If "??" equal 7B, 7C, 98 or b4 then check to see if a nozzle size was registered which is larger

第 1193 页