FUJI错误代码查询.pdf - 第218页
------------------------------ Code: 11082220 Display: Servo Power is ON Used by: MTU3,MTU4,MTU5 Cause: While the servo power was on at the MTU, the IP machine issued a command for when the servo power is off. Remedy: Re…
machine.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082001
Display: MTU is in OFF_LINE Mode
Used by: MTU3,MTU4,MTU5
Cause: When the MTU was in the off-line mode, a command for on-line use was issued by the IP
machine.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082010
Display: Usable Proper Data has not been sent to MTU
Used by: MTU3,MTU4,MTU5
Cause: Proper data is not stored in the MTU.
Remedy: Transmit Proper data to the MTU.
------------------------------
Code: 11082011
Display: Usable Sequence Data has not been sent to MTU
Used by: MTU3,MTU4,MTU5
Cause: No program is stored in the MTU.
Remedy: Transmit a program to the IP machine.
------------------------------
Code: 11082012
Display: Usable Device Data has not been sent to MTU
Used by: MTU3,MTU4,MTU5
Cause: No program is stored in the MTU.
Remedy: Transmit a program to the IP machine.
------------------------------
Code: 11082020
Display: Zero setting not Completed
Used by: MTU4
Cause: Operation was attempted even though zero setting had not been completed.
Remedy: Switch the power off and then on again to both the IP machine and the MTU, and then perform
zero setting.
------------------------------
Code: 11082170
Display: Nozzle pressing overload detected
Used by: MTU4
Details: The sensor for detecting that the subnozzle is pressing too hard is activated.
Cause:
Remedy: The subnozzle is pressing down too hard. Check the part height, and the tray pickup offset.
Adjust the sensor.
------------------------------
Code: 11082200
Display: Transmission Format Error
Used by: MTU3,MTU4,MTU5
Cause: When communication takes place between the MTU and the IP machine, if the transmitted data
is not in the correct format, due to the effects of static electricity, transmission is reattempted 3 times. In
this case transmission was attempted three times but no correct response was obtained.
Remedy: Check that the there is no machine emitting a strong magnetic field along the route of the
communication cable between the MTU and the IP machine.
第 217 页
------------------------------
Code: 11082220
Display: Servo Power is ON
Used by: MTU3,MTU4,MTU5
Cause: While the servo power was on at the MTU, the IP machine issued a command for when the servo
power is off.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082221
Display: Servo Power is OFF
Used by: MTU3,MTU4,MTU5
Cause: While the servo power was off at the MTU, the IP machine issued a command for when the servo
power is on.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082230
Display: Operation Mode is set to OPERATE
Used by: MTU3,MTU4,MTU5
Cause: While the MTU was operating, commands for use when the MTU is stopped were issued by the IP
machine.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082231
Display: Operation Mode is set to Stop
Used by: MTU3,MTU4,MTU5
Cause: While the MTU was operating, commands for use when the MTU is stopped were issued by the IP
machine.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082240
Display: Remove empty tray
Used by: MTU4
Cause: An emergency stop occurred after the last part in the tray had been picked up and before the tray
was ejected. Because the emergency stop occurred during the tray eject cycle, the MTU is unsure of the
condition of the tray. Therefore it is necessary for the operator to check the tray and remove it.
Remedy: Manually remove the empty tray.
------------------------------
Code: 11082250
Display: Operation Impossible MTU Operation Panel in Use
Used by: MTU3,MTU4,MTU5
Cause: Operation was being performed at the MTU terminal when AUTO, STEP or another command was
executed at the IP machine.
Remedy: At the MTU terminal us
------------------------------
Code: 110822EE
Display: Command can not be Executed due to Alarm
Used by: MTU3,MTU4,MTU5
Cause: While the MTU was in an error condition, an instruction to start production was issued by the IP
machine.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
第 218 页
Code: 11082310
Display: Pickup Recovery Counter Limit Reached
Used by: MTU3,MTU4,MTU5
Cause: The sub-nozzle was unable to pick up a part in the tray and therefore reattempted to pick up the
part the specified number of times, again without success.
Remedy: Check that the tray is correctly positioned and that the parts with in the tray are correctly
positioned. Also check that correct data has been specified in part data.
------------------------------
Code: 11082330
Display: Nozzle Selection Error
Used by: MTU4
Cause: A nozzle which cannot be used on the MTU was specified.
Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.
------------------------------
Code: 11082331
Display: Y Axis Deceleration Sensor is Not ON at Nozzle change
Used by: MTU4
Cause: When an attempt was made to change a nozzle, the Y axis speed reduction sensor was not on.
Remedy: Adjust the Y axis speed reduction sensor and the dog. In addition check that suitable data has
been entered for the MTU Proper data item Carrier_Position_SY.
------------------------------
Code: 11082332
Display: Z Axis Deceleration Sensor is Not ON at Nozzle change
Used by: MTU4
Cause: When an attempt was made to change a nozzle, the Z axis speed reduction sensor was not on.
Remedy: Adjust the Z axis speed reduction sensor and the dog. In addition check that suitable data has
been entered for the MTU Proper data item Parts_Pos_Zt0.
------------------------------
Code: 11082333
Display: Nozzle Pos. Sensor Error
Used by: MTU4
Cause: When the nozzle rotated, the nozzle position sensors did not turn on at the correct positions.
Remedy: Check the nozzle position sensors and the dogs.
------------------------------
Code: 11082334
Display: Nozzle Changer is Not at Retract Limit Position
Used by: MTU4
Cause: During nozzle change, the nozzle changer retract end sensor was not on.
Remedy: Adjust the nozzle changer retract end and advance end sensors.
------------------------------
Code: 11082335
Display: Nozzle Changer is Not at Forward Limit Position
Used by: MTU4
Cause: During nozzle change, the nozzle changer advance end sensor was not on.
Remedy: Adjust the nozzle changer advance end sensor and the dog.
------------------------------
Code: 11082340
Display: Parts Dropped From Sub-Nzl (Remove Part)
Used by: MTU4
Cause: A part picked up by the sub-nozzle was dropped while the Z axis was ascending.
Remedy: Remove the part which was dropped.
第 219 页