FUJI错误代码查询.pdf - 第1158页

through sensor at the in-conveyor end. Remedy: Check the X068: P.IN ARRV CK operation using I/O commands and adjust if necessary. ------------------------------ Code: 15040885 Display: UNLD-CHGMODULE CHANGE TUP Loader er…

100%1 / 5282
Cause: Abolished.
Remedy: Abolished.
------------------------------
Code: 15040877
Display: UNLD MANI RISE FAIL
Loader error: 15040877
Used by: QP132
Cause: The exit board transport upper-limit sensor went off during movement of the unloading side
manipulator.
Remedy: Make sure that the air pressure used to raise the board which is to be transported out, has not
fallen. Check the operation of the exit board transport upper-limit sensor.
------------------------------
Code: 15040880
Display: UNLD 10-SHIFT FORWARD TUP
Loader error: 15040880
Used by: QP132
Cause: The out-conveyor pallet pusher (which shifts the pallet a further 10 mm) did not reach its
extended position in the given time.
Remedy: Check the pallet pusher is at its extended position (X073: P.OUT PLT RSFT) using I/O
commands and adjust if necessary.
------------------------------
Code: 15040881
Display: UNLD 10-SHIFT BACKWARD TUP
Loader error: 15040881
Used by: QP132
Cause: The out-conveyor pallet pusher (which shifts the pallet a further 10 mm) did not reach its retract
position in the given time.
Remedy: Check the pallet pusher is at its retract position (X074: P.OUT PLT LSFT)using I/O commands
and adjust if necessary.
------------------------------
Code: 15040882
Display: UNLD TRANS FORWARD TUP
Loader error: 15040882
Used by: QP132
Cause: The pallet pusher that moves a pallet from the pallet unloader to the return-conveyor did not
finish extending in the given time.
Remedy: Check the X075: P.OUT PUSH FED operation using I/O commands and adjust if necessary.
------------------------------
Code: 15040883
Display: UNLD TRANS BACKWARD TUP
Loader error: 15040883
Used by: QP132
Cause: The pallet pusher that moves a pallet from the pallet unloader to the return-conveyor did not
finish retracting in the given time.
Remedy: Check the X076: P.OUT PUSH BED operation using I/O commands and adjust if necessary.
------------------------------
Code: 15040884
Display: UNLD-RCV CHANGE TUP
Loader error: 15040884
Used by: QP132
Cause: After being unloaded to the return-conveyor, the pallet did not activate the return-conveyor pass-
第 1157 页
through sensor at the in-conveyor end.
Remedy: Check the X068: P.IN ARRV CK operation using I/O commands and adjust if necessary.
------------------------------
Code: 15040885
Display: UNLD-CHGMODULE CHANGE TUP
Loader error: 15040885
Used by: QP132
Cause: The pallet did not activate the unloading pallet interlock when it was moved from the pallet
unloader to the changeover module.
Remedy: Check the X027: P.OUT INTERLCK operation using I/O commands and adjust if necessary.
------------------------------
Code: 15040886
Display: CHGMODULE-UNLD CHANGE TUP
Loader error: 15040886
Used by: QP132
Cause: The pallet did not activate the unloading pallet interlock when it was moved from the changeover
module to the pallet unloader.
Remedy: Check the X027: P.OUT INTERLCK operation using I/O commands and adjust if necessary.
------------------------------
Code: 15040887
Display: Chgst Bar Ext Pos Error
Loader error: 15040887
Used by: QP132
Cause: The change station bar has not reached its extended position in the time allowed.
Remedy: Check the operation of the change station bar with I/O X06C: CHG BAR FWEND and make any
necessary adjustments.
------------------------------
Code: 15040888
Display: Chgst Bar Ret Pos Error
Loader error: 15040888
Used by: QP132
Cause: The change station bar has not reached its retract position in the time allowed.
Remedy: Check the operation of the change station bar with I/O X06C: CHG BAR BWEND and make any
necessary adjustments.
------------------------------
Code: 15040901
Display: Abolished.
Used by: QP122
Cause: Abolished.
Remedy: Abolished.
------------------------------
Code: 15040A01
Display: 电路板载入异常　往复臂L
Used by: NXTP
Cause: 从前道工序到换乘传感器或者电路板到达传感器为止电路板没有到达。
Remedy: １．请确认搬运轨道间的电路板载入是否顺畅。
２．请确认换乘传感器(RX080,RX081)，电路板到达传感器(RX082)能正常检测电路板。
<img src="$LKEY_ERRIMG_MC$/15040A01.PNG">
------------------------------
Code: 15040A02
Display: 电路板载入异常　往复臂R
第 1158 页
Used by: NXTP
Cause: 从前道工序到换乘传感器或者电路板到达传感器为止电路板没有到达。
Remedy: １．请确认搬运轨道间的电路板载入是否顺畅。
２．请确认换乘传感器(RX0A0,RX0A1)、电路板到达传感器(RX0A2)能正常检测电路板。
<img src="$LKEY_ERRIMG_MC$/15040A02.PNG">
------------------------------
Code: 15040B01
Display: 通道2 电路板搬运异常
Used by: NXTP
Cause: 电路板搬运超时。
电路板在中途停止或者落下了。
Remedy: 请从通道2取出电路板。
不关闭门时不能解除此错误。
<img src="$LKEY_ERRIMG_MC$/15040B01.PNG">
------------------------------
Code: 15040B02
Display: 通道2 电路板排出异常
Used by: NXTP
Cause: 虽然从通道２送出了电路板，但是往复臂的电路板到达传感器没有在规定时间内成为电路板到达状态。
Remedy: 请检查是否在搬运轨道上有被卡住的电路板。
不打开前门进行电路板的有无确认时，不能解除错误。
<img src="$LKEY_ERRIMG_MC$/15040B02.PNG">
------------------------------
Code: 15040B03
Display: 通道2 变更宽度时有电路板错误
Used by: NXTP
Cause: 变更宽度时有电路板。
Remedy: 请取出电路板。
<img src="$LKEY_ERRIMG_MC$/15040B03.PNG">
------------------------------
Code: 15040B04
Display: 电路板载入异常　通道２
Used by: NXTP
Cause: 从前道工序到换乘到传感器为止电路板没有到达。
Remedy: １．请确认搬运轨道间的电路板载入是否顺畅。
２．请确认换乘传感器(RX063)能正常检测电路板。
<img src="$LKEY_ERRIMG_MC$/15040B04.PNG">
------------------------------
Code: 15040B05
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B06
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B07
第 1159 页