FUJI错误代码查询.pdf - 第522页

Used by: GL2 Cause: A cycle alarm has occurred for servo axis ZL.The servo axis did not reach the targeted value within the expected time. This error may be caused by interference from another object. Remedy: Make sure t…

100%1 / 5282
------------------------------
Code: 1205200C
Display: "Cycle alarm: servo LT" (IP)
Used by: IP1
Cause: A cycle alarm has occurred for servo axis LT.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 1205200D
Display: "Cycle alarm: servo RT" (IP)
Used by: IP1
Cause: A cycle alarm has occurred for servo axis RT.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 1205200E
Display: "Cycle alarm: servo X2"
Used by: IP2,IP3
Cause: A cycle alarm has occurred for servo axis X2.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 1205200F
Display: "Cycle alarm: servo Q2"
Used by: IP2
Cause: A cycle alarm has occurred for servo axis Q2.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052010
Display: "Cycle alarm: servo Z2" (IP2)
Used by: GL5,GL541,GSP5,GP551,IP2
Cause: A cycle alarm has occurred for servo axis Z2.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052011
Display: "Cycle alarm: servo S" (GSP)
Used by: GSP2,GSP3,GSP5,GP2,GP3,GP551,GP6
Cause: A cycle alarm has occurred for servo axis S. The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052012
Display: "Cycle alarm: servo ZL" (GL)
第 521 页
Used by: GL2
Cause: A cycle alarm has occurred for servo axis ZL.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052013
Display: "Cycle alarm: servo ZR" (GL)
Used by: GL2
Cause: A cycle alarm has occurred for servo axis ZR.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052014
Display: "Cycle alarm: servo Z3" (GL5)
Used by: GL5,GL541
Cause: A cycle alarm has occurred for servo axis Z3.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052015
Display: PQ Rotation Alarm
Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: The pre-theta could not be rotated within the cycle time.
Remedy: Check that the axis is not overloaded. Remove any objects that interfere with axis
movement.Check the cylinder's advance and retract sensors.
------------------------------
Code: 12052016
Display: "Servo cycle alarm FQ" (CP4), "Cycle alarm <R> FQ: Reach" (CP6)
Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: On the CP4, [fine sheeter] rotation could not be completed within the cycle time.On the CP6, FQ-
axis rotation could not be completed within the cycle time; if an <R> is displayed, the FQ-axis was being
returned (10ST).
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052017
Display: Cycle Alarm Search Error
Used by:
Cause: The pre-theta origin point cannot be found.
Remedy: Check the station 2 position sensor.
------------------------------
Code: 12052018
Display: 4st clutch NG
Used by:
Cause: The clutch did not engage at station 4.
Remedy: Check that there are no alarms at the station 4 clutch and the nozzle shaft.
------------------------------
Code: 12052019
第 522 页
Display: Cycle Alarm DF
Used by: CP5
Cause: The DF axis did not move within the preset time limit.
Remedy: Check that there is no special load on the DF axis.
------------------------------
Code: 1205201A
Display: Cycle Alarm DR
Used by: CP5
Cause: The DR axis did not move within the preset time limit.
Remedy: Check that there is no special load on the DR axis.
------------------------------
Code: 1205201B
Display: "Cycle alarm D1", "Cycle alarm D1: Reach" (CP6)
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643,IP3
Cause: A cycle alarm has occurred for the D1-axis. The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Remove any interfering objects.
------------------------------
Code: 1205201C
Display: "Cycle alarm D2", "Cycle alarm D2: Reach" (CP6)
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643,IP3
Cause: A cycle alarm has occurred for the D2-axis. The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Remove any interfering objects.
------------------------------
Code: 1205201E
Display: "Cycle alarm <R> NC: Reach" (CP6)
Used by: CP6,CP6M,CP65,CP652C,CP642.CP643
Cause: NC-axis rotation could not be completed within the cycle time; if an <R> is displayed, the NC-axis
was being returned (18ST).
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 1205201F
Display: "Cycle alarm <R> FRQ: Reach" (CP6)
Used by: CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: FRQ-axis rotation could not be completed within the cycle time; if an <R> is displayed, the FQ-
axis was being returned (12ST).
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052020
Display:
Used by: IP3,QP132
Cause: The axis moved beyond its limit.
Remedy: Check the coordinates in the program and the values in Proper data.
------------------------------
Code: 12052021
Display:
第 523 页