FUJI错误代码查询.pdf - 第54页

Remedy: Refer to the above device numbers and enter correct values for the package type in Part data. ------------------------------ Code: 11011710 Display: Used by: IP2 Cause: An attempt was made to use devices 1~3 (85~…

100%1 / 5282
Code: 1101169E
Display:
Used by: IP2
Cause: There has been a mark reading sequence found after in the placing sequences (sequences
1751~1875). Fiducial mark or block skip mark reading sequences must all be executed before any placing
sequences.
Remedy: Alter the production program so that the mark reading sequences are executed before any
placing sequences. The relevant sequences for this message are 1751~1875.
------------------------------
Code: 1101169F
Display:
Used by: IP2
Cause: There has been a mark reading sequence found after in the placing sequences (sequences
1876~2000). Fiducial mark or block skip mark reading sequences must all be executed before any placing
sequences.
Remedy: Alter the production program so that the mark reading sequences are executed before any
placing sequences. The relevant sequences for this message are 1876~2000.
------------------------------
Code: 11011700
Display:
Used by: IP2
Cause: On the IP2, an unsupported feeder type has been specified in Part data (somewhere in devices
1~25).
Remedy: Check the above mentioned devices and enter the correct feeder type in Part data.
------------------------------
Code: 11011701
Display:
Used by: IP2
Cause: On the IP2, an unsupported feeder type has been specified in Part data (somewhere in devices
26~37).
Remedy: Check the above mentioned devices and enter the correct feeder type in Part data.
------------------------------
Code: 11011702
Display:
Used by: IP2
Cause: On the IP2, an unsupported feeder type has been specified in Part data (somewhere in devices
51~75).
Remedy: Check the above mentioned devices and enter the correct feeder type in Part data.
------------------------------
Code: 11011703
Display:
Used by: IP2
Cause: On the IP2, an unsupported feeder type has been specified in Part data (somewhere in devices
76~87).
Remedy: Check the above mentioned devices and enter the correct feeder type in Part data.
------------------------------
Code: 11011704
Display: 11011704
Used by: IP2
Cause: A package type which is not supported on the FIP-II has been set in Part data. The relevant
device is within the range D101 ~ 110 or D111 ~ 120.
第 53 页
Remedy: Refer to the above device numbers and enter correct values for the package type in Part data.
------------------------------
Code: 11011710
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 1~125.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011711
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 126~250.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011712
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 251~375.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011713
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 376~500.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011714
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 501~625.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011715
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
第 54 页
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 626~750.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011716
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 751~875.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011717
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 876~1000.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011718
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 1001~1125.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 11011719
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 1126~1250.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 1101171A
Display:
Used by: IP2
Cause: An attempt was made to use devices 1~3 (85~87) when an MTU is installed. When there is an
MTU on the machine, these devices cannot be used. This is to prevent possible interference between
feeders and the carrier. This message applies to sequences 1251~1375.
Remedy: Check the above mentioned sequences and alter the production program so that devices 1~3
(85~87 if there is a left MTU) are not used.
------------------------------
Code: 1101171B
第 55 页