FUJI错误代码查询.pdf - 第1195页

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83, 87, 88, 98, 9D or B4 the specified number of leads could not be found. Remedy: Check the part data, especially th…

than the part size. As a rule, the size of the black plate attached to chucks is entered at that setting item.

------------------------------

Code: 1CA??016

Display: 1CA??016

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 8D or

8E then the image cannot be converted to binary data.Remedy: If "??" equal 8D or 8E then this is a highly

unusual internal error. Contact your Fuji service representative if this error occurs.

Remedy:

------------------------------

Code: 1CA??017

Display: 1CA??017

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal 8D or

8E then processing is not possible because the space between bumps is too narrow.

Remedy: If "??" equal 8D or 8E then use a bump array where the distance between the bumps (leads) is

1/6 or more of the average vertical and horizontal body size.

------------------------------

Code: 1CA??021

Display:

Used by:

Cause: ?? is the PD Vision_type in hexadecimal numbers. If ?? = 64, 69, 78, 79, 7A, 7D, 7E, or 7F ,the

coarse position cannot be determined. If ?? = 7B, 7C, 80, 81, 82, 83, 87, 88, 8C, E6, E7, E9, EB, EC, 98,

or 9D, less than half the specified leads were found. If ?? = 99, part cannot be found.

Remedy: If ?? = 64, 69, 78, 79, 7A, 7D, 7E, or 7F ,check that there is no problem with image brightness,

and check that there is no problem with a dirty background. If ?? = 7B, 7C, 80, 81, 82, 83, 87, 88, 8C,

E6, E7, E9, EB, EC, 98, or 9D, check for errors in the part data. In particular, check the lead size data. If

?? = 99, the part which should be detected cannot be found. Check to see if the part appears on the

image display.

------------------------------

Code: 1CA??022

Display: 1CA??022

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 8C, E6, E7, E9, EB, EC, 98, or 9D fewer than half of the leads specified in part data could be found. If

"??" equal 8D or 8E then part position cannot be determined because fewer than 2 bumps were found.

Remedy: If ?? is 7B, 7C, 80, 81, 82, 83, 87, 8C, E6, E7, E9, EB, EC, 98, or 9D check the part data,

especially the number of leads and the lead size. If "??" equal 8D or 8E then check the part data. Also

check to see if the bump sizes are correct. Or, increase the bump size tolerance value.

------------------------------

Code: 1CA??023

Display: 1CA??023

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, or B4 the blob area is incorrect.

Remedy: This is an internal processing error which should not normally occur. If this error occurs, notify

Fuji.

------------------------------

Code: 1CA??024

Display: 1CA??024

Used by:

第 1194 页

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, 9D or B4 the specified number of leads could not be found.

Remedy: Check the part data, especially the lead size.

------------------------------

Code: 1CA??025

Display: 1CA??025

Used by:

Cause: ?? indicates in hexadecimal notation the Vision_type in part data. If ?? is 7B, 7C, 80, 81, 82, 83,

87, 88, 98, 9D or B4 extra leads have been found.

Remedy: Check that the part data is correct.

------------------------------

Code: 1CA??030

Display: 1CA??030

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E or F0 this signifies that the segments such as the leads

that should have been measured do not exist.

Remedy: In this case the Result data item in EL_data of part data was set to "0" for all of the elements.

Set the Result data item to "1" for all measured segments.

------------------------------

Code: 1CA??031

Display: 1CA??031

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, AA, or F0 this indicates that lead inspection could not

be carried out. If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, or 98 then the input parameters are incorrect.

If "??" equals 8C, E6, E7, E9, EB, or EC this signifies that the part angle was not found. If "??" equal B4

excessive mismatch between data and actual part was found.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, AA or F0 then the lead

inspection has failed for some reason. Make sure that there are no mistakes in the EL_data in part data.

If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, or 98 this is an internal error that normally does not occur.

If it does occur contact Fuji. If "??" equals 8C, E6, E7, E9, EB, or EC then too many leads were not found

making it impossible to determine the angle. Make sure that the part data is correct and in particular

check the size of the leads. If "??" equal B4 check for errors in the part data. In particular, check lead

information.

------------------------------

Code: 1CA??032

Display: 1CA??032

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, or F0 this indicates that there was no inspected

segment for determining the X-dimension of the part position. If "??" equals 7B, 7C, 80, 81, 82, 83, 87,

88, 98, or 9D then the correct part angle was not found. If "??" equals 8C, E6, E7, E9, EB, or EC this

indicates that the part positioning phase could not be carried out. If "??" 8D or 8E equals coarse

positioning cannot be performed.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, or F0 this means that

the inspection of leads has failed for some reason. Leads could not be found for the X-dimension

inspection results to be used for part positioning. Make sure that the data set in P_pattern in part data is

appropriate. If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, 98, or 9D then make sure that the part data is

correct and in particular that the lead size setting matches the actual size of the leads. If "??" equals 8C,

E6, E7, E9, EB, or EC then the external ow of leads could not be detected. Check the part data and if the

第 1195 页

part data is correct then make sure there is not too much displacement in the part pickup status. If "??"

equals 8D or 8E Check for the following:

o Part protruding from the camera's field of vision.

o Image brightness problem.

o Image problem caused by dust, etc., on the part background.

------------------------------

Code: 1CA??033

Display: 1CA??033

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0 or F0 this indicates that there was no inspected

segment for determining the Y-dimension of the part position. If "??" equals 8C, 8D, 8E, E6, E7, E9, EB,

or EC this indicates that the number of leads found is less than the specified number of leads. If "??"

equals 98 or 9D then there was alead recognition failure.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, or F0 this means that

the inspection of leads has failed for some reason. Leads could not be found for the Y-dimension

inspection results to be used for part positioning. Make sure that the data set in P_pattern in part data is

appropriate. If "??" equals 8C, 8D, 8E, E6, E7, E9, EB, or EC this signifies that part positioning was

carried out but that the number ofleads detected was less than the number of leads specified. Decrease

the Check_limit setting in part data. f "??" equals 98 or 9D then make sure the part data is correct. In

particular verify that the lead size has been input correctly.

------------------------------

Code: 1CA??034

Display: 1CA??034

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, or F0 this indicates that the leads used for determining positioning could not be

detected. If "??" equals 96, 97, 99, 9B, 9C, or 9E this signifies that there was no data for calculating the

angles. If "??" equal A0 data required for angle calculation does not exist.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, or F0 this means that the leads could not be found

for the inspection results to be used for part positioning. Make sure that the data set in P_pattern in part

data is appropriate. If "??" equals 96, 97, 99, 9B, 9C, or 9E then verify that the part data is correct. If "??"

equals A0 check for errors in the part data.

------------------------------

Code: 1CA??035

Display: 1CA??035

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0 or F0 this signifies that a lead was detected in a

location where no lead was expected.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0 or F0 then make sure

the lead arrangement data is correct. Also verify that the correct part is being used.

------------------------------

Code: 1CA??036

Display: 1CA??036

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7B, 7C, 7D, 7E, 7F, 96, 97, 98, 99, 9B, 9C, 9D, 9E, A0, B4, or F0 this indicates that an excess

lead was discovered whenthe first-last lead pitch check was carried out.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7B, 7C, 7D, 7E, 7F, 96, 97, 98, 99, 9B, 9C, 9D, 9E, A0, B4, or

F0 then confirm that the correct part is being used.

第 1196 页