FUJI错误代码查询.pdf - 第1853页
------------------------------ Code: 21001043 Display: Illegal argument Used by: Cause: The start-up parameters are incorrect. Remedy: Correct the parameters (set the overwrite mode, change the file directory, etc.) ----…
------------------------------
Code: 2100001A
Display: Timer_ev link error
Used by:
Cause: The timer event could not be linked.
Remedy: Reboot MCS.
------------------------------
Code: 2100001B
Display: Strings file expand error (***)
Used by:
Cause: The message file could not be expanded.
Remedy: Reboot MCS. If the problem persists, reinstall the system.
------------------------------
Code: 2100001C
Display: Logfile save error
Used by:
Cause: The log file could not be written to the hard disk.
Remedy: Check how much space remains in the hard disk. Check the disk partitions. If there is not
enough remaining space, delete all unnecessary files and check that the disk is in good condition. If the
error recurs and there is space available, it is possible that the disk is damaged.
------------------------------
Code: 2100001D
Display: Version error machine No. **(****)
Used by:
Cause: The data already in the machine interfered with the data in the version being transmitted to the
machine.
Remedy: Reset-start the machine (machine No.**) and re-boot MCS.
------------------------------
Code: 2100001E
Display: Version check time over
Used by:
Cause: The version being transmitted to the machine could not be checked.
Remedy: Turn off the machine power, re-boot MCS, re-boot the machine and re-transmit the version.
------------------------------
Code: 2100001F
Display:
Used by:
Cause: The production event file could not be read.
Remedy: Reinstall and reboot MCS. If this error recurs, there is the possibility that the file is damaged.
------------------------------
Code: 21001000
Display:
Used by:
Cause: The transmission sub-process could not be carried out due to a system error.
Remedy: Re-install the Host communication software.
------------------------------
Code: 21001041
Display: Illegal function code/command
Used by:
Cause: The start-up command was incorrect.
Remedy: Correct the specified start-up command.
第 1852 页
------------------------------
Code: 21001043
Display: Illegal argument
Used by:
Cause: The start-up parameters are incorrect.
Remedy: Correct the parameters (set the overwrite mode, change the file directory, etc.)
------------------------------
Code: 210010CF
Display: Process Memory full
Used by:
Cause: Sufficient memory area could not be allocated as the work area to carry out conversion of
transmitted data.
Remedy: Check that there is sufficient memory to operate the system. If there isn't, perform a system
reset.
------------------------------
Code: 210010D3
Display: End of file
Used by:
Cause: The end of file (EOF) character was detected while a file was being read.
Remedy: The file format is incorrect. The file has probably been damaged for some reason. Run the
communication function again with a different file. If the error occurs again with the new file.
------------------------------
Code: 210010D6
Display: File not accesible
Used by:
Cause: The file is write protected, so it is not possible to write data to the file or to delete the file.
Remedy: Use the File Services function from the UCI menu to cancel the write protection.
------------------------------
Code: 210010D7
Display: Bad path name
Used by:
Cause: The directory (path) is specified incorrectly.
Remedy: Specify the directory correctly.
------------------------------
Code: 210010D8
Display: File not found
Used by:
Cause: A non-existent file was specified.
Remedy: Check the file name.
------------------------------
Code: 210010DA
Display: File already exists
Used by:
Cause: A Part Data file with the same name already exists, and the current file cannot be loaded.
Remedy: Set the overwrite mode to YES to replace the contents of the existing file, or specify a new file
name.
------------------------------
Code: 210010DD
Display: Module not found
Used by:
Cause: The specified module does not exist, or could not be loaded.
第 1853 页
Remedy: Re-install the Host communication software.
------------------------------
Code: 210010F4
Display: Read error
Used by:
Cause: An error occurred while reading data from the disk.
Remedy: Check that the file can be read in the editor. If not, the file has been destroyed.
------------------------------
Code: 210010F5
Display: Write error
Used by:
Cause: An error occurred while writing data to the disk.
Remedy: Check the condition of the disk (available memory, partitions, etc.).
------------------------------
Code: 210010F6
Display: Device not ready
Used by:
Cause: The disk is not moving.
Remedy: Re-boot MCS.
------------------------------
Code: 210010F8
Display: Media full
Used by:
Cause: There is no space available on the disk.
Remedy: Delete unused files from the disk.
------------------------------
Code: 21001719
Display: Connection time over
Used by:
Cause: Reply or communication was not completed within the fixed time.
Remedy: Start again from the beginning. If there is still a problem, check the cable connections and MCS
settings.
------------------------------
Code: 21001751
Display: File descriptor not found
Used by:
Cause: The file descriptor required for data conversion does not exist.
Remedy: Re-install the Host communication software.
------------------------------
Code: 21001752
Display: File descriptor format error
Used by:
Cause: The contents of the file descriptor are not correct.
Remedy: Re-install the Host communication software.
------------------------------
Code: 21001761
Display: Character substitution file error
Used by:
Cause: The character substitution file is incorrect.
Remedy: Check the file.
------------------------------
第 1854 页