semi合集-English.pdf - 第1974页

SEMI E54.4-0704 © SEMI 1997, 2004 9 APPENDIX 1 PROTOCOL SPECIF ICATION SHEETS NOTICE : This appe ndix is not an official part o f SEMI E54.4 a nd is not intended to m odify or supercede the official standard. Determinati…

100%1 / 7923
SEMI E54.4-0704 © SEMI 1997, 2004 8
9 Specific Device Model Mappings
9.1 This section provides for the mapping of network-
visible specific device structure and behavior, specified
in a SEMI standard SDM specification, to the DN
network. Each subsection is devoted to a single SDM
specification (e.g., 9.1: Mass Flow Controller).
Additional SDM mappings are added as sub-sections to
this NCS specfication according to SEMI guidelines
and the guidelines of the SEMI SAN Interoperability
standard.
SEMI E54.4-0704 © SEMI 1997, 2004 9
APPENDIX 1
PROTOCOL SPECIFICATION SHEETS
NOTICE: This appendix is not an official part of SEMI E54.4 and is not intended to modify or supercede the
official standard. Determination of the suitability of the material is solely the responsibility of the user. This
appendix contains a set of protocol specification sheets. Compliance to this NCS necessarily requires adherence to
this set of protocol specification sheets (see Section 8.1).
A1-1 The protocol specification set of sheets contains the following components:
• A General Device Data/Physical ConformanceData/ DeviceNet Communication Data statement of compliance.
(Form F_1, 1 page.)
• DeviceNet required object implementation statements of compliance (for Identity, Message Router, and
DeviceNet objects, see Section 7). (Forms F_2 through F_5, 4 pages.)
• NCS - DeviceNet required object implementation statements of compliance (for Device Manager and
Sensor/Actuator/Controller objects, see Section 7). (Form F_6, 2 pages.)
• Open object- and vendor- specific implementation templates (for utilization by SDMs, vendors, etc.). (Forms
F_6 through F_7, 2 pages.)
A1-1.1 Note that these protocol specification sheets are aligned with DeviceNet specifications for “Statement of
Compliance” documentation, available with the DeviceNet specification from ODVA. Detailed instructions on
completing these forms are in this “Statement of Compliance” documentation. The set of protocol specification
sheets begins on the following page.
SEMI E54.4-0704 © SEMI 1997, 2004 10
DeviceNet Statement of Compliance
Complete this form using the definitions previously outlined.
Fill in the blank or X the appropriate box
Conforms to DeviceNet Specification Volume I - Release _____________________
Volume II - Release _____________________
Vendor Name _____________________
Device Profile Name _____________________
Product Catalog Number _____________________
General
Device
Data
Product Revision _____________________
Network Power Consumption (Max) _______A @ 11V dc (worst case)
Connector Style Open-Hardwired ❑ Sealed-Mini ❑
DeviceNet
Physical
Conformance
Data
Open-Pluggable ❑ Sealed-Micro ❑
Isolated Physical Layer Yes ❑
No ❑
LEDs Supported Module ❑ Combo Mod/Net ❑
Network ❑ I/O ❑
DIP Switch ❑ Software-Settable ❑
Other__________________________________________________
Default MAC ID _____________________
Communication Rate Setting DIP Switch ❑ Software-Settable ❑
Other__________________________________________________
Communication Rates Supported 125k bit/s
❑ 500k bit/s ❑
250k bit/s ❑
❑ Predefined Master/Slave Connection
Set
Group 2 Client ❑ Group 2 Only Client ❑
DeviceNet
Communication
Data
Group 2 Server ❑ Group 2 Only Server ❑
❑ Dynamic Connections Supported
(UCMM)
Group 1 ❑ Group 3 ❑
Group 2 ❑
Fragmented Explicit Yes ❑
Messaging Implemented No ❑
If yes, Transmission Time Out_______________________ms
Typical Target Address Class___________________
Instance_________________
Attribute_________________
X Get to indicate that attribute value is returned by the use of Get_Attribute_Single service.
X Set to indicate that attribute value is written to by the use of Set_Attribute_Single service.
F_ 1