semi合集-English.pdf - 第918页

SEMI E118-1104 E © SEMI 2002, 2004 12 Parameter Req/Ind Rsp/Conf Description Attribute Values M - Attribute Values. Result Status - M Result info rmati on on the status of the requ est. Status - M Status information. 11.…

100%1 / 7923
SEMI E118-1104
E
© SEMI 2002, 2004 11
11.4.4 Get Status
11.4.4.1 Get Status is a required service used to get the current status of the WIDR. The upstream controller may
request current status at any time.
Table 11 Get Status Service Definition
Parameter Req/Ind Rsp/Conf Description
Head ID M M Specifies Head or Subsystem.
Result Status - M Result information on the status of the request.
Status - M Status information.
11.4.5 Perform Diagnostics
11.4.5.1 Perform Diagnostics is an optional service used to request the WIDR perform its internal diagnostics. The
supplier shall document the specific diagnostics performed.
Table 12 Perform Diagnostics Service Definition
Parameter Req/Ind Rsp/Conf Description
Head ID M M Specifies Head or Subsystem.
Action C Specifies diagnostic action to perform.
Result Status - M Result information on the status of the request.
Status - M Status information.
11.4.6 Read WID
11.4.6.1 Read WID is used to request the WID be read by an ID Reader Head. This service is a fundamental
requirement.
Table 13 Read WID Service Message Parameter Definition
Parameter Req/Ind Rsp/Conf Description
Head ID M M Specifies Head.
Wafer ID - M Wafer ID.
Result Status - M Result information on the status of the request.
Status - M Status information.
11.4.7 Reset
11.4.7.1 Reset is used to re-initialize the WIDR.
Table 14 Reset Service Definition
Parameter Req/Ind Rsp/Conf Description
Result Status - M Result information on the status of the request.
11.4.8 Set Attributes
11.4.8.1 Set Attributes is used to set attributes of the WIDR. This is an optional service. Attempts to set attributes
with read-only (RO) access shall be denied. Attribute values returned are those as read following the set operation.
Table 15 Set Attributes Service Definition
Parameter Req/Ind Rsp/Conf Description
Head ID M M Specifies Head or Subsystem.
Attribute ID M - AttributeIDs.
SEMI E118-1104
E
© SEMI 2002, 2004 12
Parameter Req/Ind Rsp/Conf Description
Attribute Values M - Attribute Values.
Result Status - M Result information on the status of the request.
Status - M Status information.
11.4.9 Read WIDC is used to read the Wafer ID with the 2D Code Read Condition. This is an optional service.
Table 16 Read WIDC Service Definition
Parameter Req/Ind Rsp/Conf Description
Head ID M M Specifies Head.
Wafer ID - M Wafer ID.
Result Status - M Result information on the status of the request.
Status - M Status information.
2D Code Condition - M 2D Code Read Condition.
11.5 Service Operability
11.5.1 Some services are performed by the WIDR and others are logically performed by the individual heads. It is
expected that the WIDR will support multiple interleaved transactions to the various independent logical units.
Table 17 shows which of the various services can be performed by the WIDR when the WIDR and its heads are in
various individual states. Note that when in the initializing state after power-up or the reset service, the WIDR may
not be able to communicate.
Table 17 Valid Services per State
Service
Set Attributes
Reset
Read WID
Perform
Diagnostics
Get Status
Get Attributes
ChangeState
Read WIDC
WIDR State
INITIALIZING
IDLE X X X X X X X X
BUSY X
MAINTENANCE X X X X X X X X
Head State
NOT OPERATING X
IDLE X
BUSY X
12 Event Notifications
12.1 Event Notification is an optional capability where the WIDR is able to detect events and report state and status
changes independently of a service request from the upstream controller.
SEMI E118-1104
E
© SEMI 2002, 2004 13
NOTICE: SEMI makes no warranties or representations as to the suitability of the standards set forth herein for any
particular application. The determination of the suitability of the standard is solely the responsibility of the user.
Users are cautioned to refer to manufacturer's instructions, product labels, product data sheets, and other relevant
literature, respecting any materials or equipment mentioned herein. These standards are subject to change without
notice.
By publication of this standard, Semiconductor Equipment and Materials International (SEMI) takes no position
respecting the validity of any patent rights or copyrights asserted in connection with any items mentioned in this
standard. Users of this standard are expressly advised that determination of any such patent rights or copyrights, and
the risk of infringement of such rights are entirely their own responsibility.