semi合集-English.pdf - 第6234页
SEMI G47-88 © SEMI 1988 1 SEMI G47-88 SPECIFICA TION FOR PLASTIC MOLDED QUA D FLAT PA CK LEADFRAMES 1 Preface This specification defines the acceptance criteria for leadframes desi gned for as sembly of JEDEC registered …
SEMI G46-88 © SEMI 1988 10
NOTICE: These standards do not purport to address
safety issues, if any, associated with their use. It is the
responsibility of the user of these standards to establish
appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
SEMI makes no warranties or representations as to the
suitability of the standards set forth herein for any
particular application. The determination of the
suitability of the standard is solely the responsibility of
the user. Users are cautioned to refer to manufacturer’s
instructions, product labels, product data sheets, and
other relevant literature respecting any materials
mentioned herein. These standards are subject to
change without notice.
The user’s attention is called to the possibility that
compliance with this standard may require use of
copyrighted material or of an invention covered by
patent rights. By publication of this standard, SEMI
takes no position respecting the validity of any patent
rights or copyrights asserted in connection with any item
mentioned in this standard. Users of this standard are
expressly advised that determination of any such patent
rights or copyrights, and the risk of infringement of such
rights, are entirely their own responsibility.
Copyright by SEMI® (Semiconductor Equipment and Materials
International), 3081 Zanker Road, San Jose, CA 95134. Reproduction o
f
the contents in whole or in part is forbidden without express written
consent of SEMI.
SEMI G47-88 © SEMI 19881
SEMI G47-88
SPECIFICATION FOR PLASTIC MOLDED QUAD FLAT PACK
LEADFRAMES
1 Preface
This specification defines the acceptance criteria for
leadframes designed for assembly of JEDEC registered
publication 95 standard outlines for “Plastic Quad Flat
Pack 0.025" lead spacing (gull wing) packages”. It is a
design guideline for packaging engineers, leadframe
stampers and etchers, mold and trim/form tooling
manufacturers. It has been developed to meet the
requirements of assemblers using automatic and manual
equipment.
2 Applicable Documents
2.1 SEMI Specifications
SEMI G4 — Specification, Integated Circuit Leadfame
Materials in the Production of Stamped Frames
SEMI G18 — Specification, Integrated Circuit
Leadframe Materials Used in the Production of Etched
Frames
SEMI G10 — Standard Method, Mechanical
Measurement for Plastic Package Leadframes
SEMI G21 — Specification, Plating Integrated Circuit
Leadframes
2.2 ANSI Specification
1
Y 14.5M-1982 — Dimensioning and Tolerancing
2.3 JEDEC Specification
2
Registration 95 — Plastic Quad Flat Pack, 0.025" Lead
Spacing (Gull Wing)
2.4 Military Specification
3
MIL-STD-105 — Sampling Procedures and Tables for
Inspection by Attributes
3 Selected Definitions
burr — a fragment of excess material either horizontal
or vertical attached to the leadframe.
camber — curvature of the leadframe strip edge (see
Figure 1).
1 ANSI, 1430 Broadway, New York, NY 10018
2 Military Standards, Naval Publications and Form Center, 5801
Tabor Ave., Philadelphia, PA 19120
3 JEDEC, 2001 Eye Street, N.W., Washington, D.C. 20006
coil set — Longitudinal bowing of the leadframe (see
Figure 2).
Figure 1
Camber
coined area — that area at the tip end of the bond
fingers coined to produce a flattened area for functional
use (see Figure 3).
Figure 2
Coil Set
crossbow — transverse bowing of the leadframe (see
Figure 4).
lead twist — angular rotation of bonding fingers (see
Figure 5).
pits — shallow surface depressions or craters in the
leadframe material.
true position circle — that circle with its center
positioned at the center of the coined lead defines the
design position of the lead tip.
SEMI G47-88 © SEMI 1988 2
Figure 3
Coined Area
Figure 4
Crossbow
Figure 5
Lead Twist
4 Ordering Information
Purchasing orders for leadframes for plastic molded
quad flat pack packages furnished to this specification
shall include the following items:
4.1 Drawing no. and revision leve l.
4.2 Material, alloy specification.
4.3 Lead count, and confirming no . of units per strip.
4.4 Requirement for material certification.
4.5 Leadframe plating specifications.
5 Dimensions
5.1 Tables 1, 2, 3, and 4.
5.2 Reference Figures 6 and 7 and Details A and B.
6 Defect Limits and Parameters (to measure,
see SEMI G10, Standard Method for
Mechanical Measurement for Plastic Package
Leadframes)
6.1 Lead Tip Width
6.1.1 Minimum Lead Tip Width — Shall be as agreed
to between supplier and purchaser.
6.1.2 Minimum Flat Wire Bonding Area — 80% of
nominal lead width and 0.025" (0.635 mm) in length.
6.2 Coining and Metal Clearance
6.2.1 Coined Depth — 0.0005" (0.013 mm) minimum
to 30% material thickness maximum (stamped frames
only).
6.2.2 Dimensions shown on drawings are before
coining.
6.2.3 Maximum Coining Bulge — (Stamped frame
only) shall not exceed 0.002" (0.051 mm) per edge and
shall be governed by metal to metal clearance
requirements (lead to lead and lead to pad).
6.2.4 Metal-to-Metal Clearance — Shall be as agreed
to between supplier and purchaser.
6.3 Lead Twist — Shall not exceed 3.5 or 0.0006"
(0.015 mm) per 0.001" (0.254 mm) of lead width.
6.4 Burrs — Shall be firmly attached and able to
withstand a probe force of 10 grams. All burrs vertical
and horizontal in any location shall not exceed 0.001"
(0.0254 mm).
6.5 Die Pad Tilt and Flatness — (See SEMI G10 for
measurement method.)
6.5.1 Tilt — 0.001" (0.025 mm) maximum per 0.100"
(2.54 mm) of length or width in the undepressed state,
and 0.002" (0.051 mm) maximum per 0.160" (4.06
mm) of length or width in the depressed state, when
measuring corner to corner: overall maximum not to
exceed a total of 0.006" (0.152 mm).
6.5.2 Flatness — 0.0002" (0.005 mm) per 0.100"
(2.54 mm) pad length when measuring from the center
to the average of four corners. The corners are defined
at 0.005" (0.127 mm) from each edge.
6.6 Pits and Slug Marks
6.6.1 Within the functional area and on external leads,
no slug marks and pits shall exceed 0.0003" (0.008