semi合集-English.pdf - 第6919页

SEMI S8-0705 © SEMI 1995, 2005 16 Section Indicator Acceptance Criteria Metric Units (US Customary Units) Actual Conforms/Does N ot Conform/Not Applicable 9.1.2 Location of infr equent ly used and/or critical controls. M…

100%1 / 7923
SEMI S8-0705 © SEMI 1995, 2005 15
Section Indicator
Acceptance Criteria
Metric Units (US Customary Units)
Actual
Conforms/Does
N
ot Conform/Not
Applicable
8.2.2 Height of video display terminal (stacked
monitors), does not include touchscreens,
measured from floor to top line of top monitor.
maximum 1400 mm (55 in.)
minimum 940 mm (37 in.)
The primary monitor in a stacked
configuration is the bottom
monitor.
8.2.3 Tilt angle of video display terminal greater than
55 inches in height to top of screen. This line
item becomes significant in the event that the
maximum height criteria cannot be met.
Downward minimum 15 degrees
8.2.4 Height of touch screen monitor. maximum 1070 mm (42 in.)
measured from floor to highest
active pad on the screen
minimum 760 mm (30 in.)
measured from floor to lowest
active pad on the screen
See §9 for horizontal reach criteria.
8.3 Display characteristics
8.3.1 Lateral distance from the centerline of the
display to the centerline of the input device(s).
See MIL-STD-1472 for a depiction of this.
maximum 320 mm (12.6 in.)
8.3.2 Character height (Specific to Chinese, Korean,
and Japanese characters.)
Character height is greater than or
equal to the viewing distance
divided by 143. Recommended
viewing distance is between 457
mm (18 in.) and 762 mm (30 in.)
8.3.3 Character height (All characters other than
Chinese, Korean, and Japanese.)
Character height is greater than or
equal to the viewing distance
divided by 215. Recommended
viewing distance is between 457
mm (18 in.) and 762 mm (30 in.)
9
Hand Control Location (These criteria only
apply to controls, tools, and materials accessed
for routine production operation and
maintenance.)
9.1 Standing station
#1
9.1.1 Vertical location of very infrequently used
controls (controls used less often than once
every 24 hours) measured from the standing
surface to the centerline of the control.
maximum 1640 mm (64.5 in.)
minimum 0 mm (0 in.)
SEMI S8-0705 © SEMI 1995, 2005 16
Section Indicator
Acceptance Criteria
Metric Units (US Customary Units)
Actual
Conforms/Does
N
ot Conform/Not
Applicable
9.1.2 Location of infrequently used and/or critical
controls. Maximum reaches are indicated for
various heights. Reaches are measured from the
leading edge of the equipment or obstacle.
Controls should not be located above 1638 mm
(64.5 in.) or below 838 mm (33 in.). Interpolate
for intermediate values.
Height of 1638 mm (64.5 in.)
Height of 1524 mm (60 in.)
Height of 1422 mm (56 in.)
Height of 1321 mm (52 in.)
Height of 1219 mm (48 in.)
Height of 1118 mm (44 in.)
Height of 1016 mm (40 in.)
Height of 914 mm (36 in.)
Height of 838 mm (33 in.)
reach 254 mm (10.0 in.)
reach 368 mm (14.5 in.)
reach 432 mm (17.0 in.)
reach 470 mm (18.5 in.)
reach 483 mm (19.0 in.)
reach 470 mm (18.5 in.)
reach 394 mm (15.5 in.)
reach 292 mm (11.5 in.)
reach 178 mm (7.0 in.)
9.1.3 Location of frequently used controls. Maximum
reaches are indicated for various heights.
Reaches are measured from the leading edge of
the equipment or obstacle. Controls should not
be located above 1270 mm (50 in.) or below
940 mm (37 in.). Interpolate for intermediate
values.
Height of 1270 mm (50 in.)
Height of 1219 mm (48 in.)
Height of 1168 mm (46 in.)
Height of 1118 mm ( 44 in.)
Height of 1067 mm (42 in.)
Height of 1016 mm (40 in.)
Height of 940 mm (37 in.)
reach 292 mm (11.5 in.)
reach 330 mm (13.0 in.)
reach 368 mm (14.5 in.)
reach 394 mm (15.5 in.)
reach 406 mm (16.0 in.)
reach 394 mm (15.5 in.)
reach 318 mm (12.5 in.)
9.2 Seated station
#2
9.2.1 Location of infrequently used and/or critical
controls. Maximum reaches are indicated for
various heights. Reaches are measured from the
leading edge of the work surface or obstacle.
Controls should not be located above 1397 mm
(55 in.) or below 533 mm (21 in.). Interpolate
for intermediate values.
Height of 1397 mm (55 in.)
Height of 1270 mm (50 in.)
Height of 1168 mm (46 in.)
Height of 1067 mm (42 in.)
Height of 965 mm (38 in.)
Height of 864 mm (34 in.)
Height of 762 mm (30 in.)
Height of 660 mm (26 in.)
Height of 533 mm (21 in.)
reach 356 mm (14.5 in.)
reach 432 mm (17.0 in.)
reach 470 mm (18.5 in.)
reach 483 mm (19.0 in.)
reach 483 mm (19.0 in.)
reach 470 mm (18.5 in.)
reach 445 mm (17.5 in.)
reach 381 mm (15.0 in.)
reach 254 mm (10.0 in.)
SEMI S8-0705 © SEMI 1995, 2005 17
Section Indicator
Acceptance Criteria
Metric Units (US Customary Units)
Actual
Conforms/Does
N
ot Conform/Not
Applicable
9.2.2 Location of frequently used controls. Maximum
reaches are indicated for various heights.
Reaches are measured from the leading edge of
the work surface or obstacle. Controls should
not be located above 1067 mm (42 in.) or below
762 mm (30 in.). Interpolate for intermediate
values.
Height of 1067 mm (42 in.)
Height of 1016 mm (40 in.)
Height of 965 mm (38 in.)
Height of 914 mm (36 in.)
Height of 864 mm (34 in.)
Height of 813 mm (32 in.)
Height of 762 mm (30 in.)
reach 330 mm (13.0 in.)
reach 368 mm (14.5 in.)
reach 394 mm (15.5 in.)
reach 406 mm (16.0 in.)
reach 419 mm (16.5 in.)
reach 419 mm (16.5 in.)
reach 419 mm (16.5 in.)
10 Workstation Design
10.1 Standing station
#1
10.1.1 Work surface edge radius where the operator
can assume a static posture in contact with the
edge.
minimum 6.4 mm (0.25 in.) radius
10.1.2 Height of keyboard, trackball, or mouse (to
home row, top of ball/mouse).
NOTE: In applications where input devices
(keyboard, trackball, or mouse) are used more
like machine controls (intermittent one finger
entry on the keyboard, intermittent short term
use of the mouse or trackball) than for standard
typing (continuous use of keyboard for entry of
long character strings, extended use of trackball
or mouse in graphical environment), it is
appropriate to use the height and reach locations
described in §9, Hand Control Location
(standing station).
maximum 1020 mm (40 in.)
minimum 970 mm (38 in.)
10.1.3 Height of microscope eyepieces. Should be
adjustable through at least this range.
Range includes 1270 mm (50 in.) to
1730 mm (68 in.)
10.2 Seated station
#2
10.2.1 Height of keyboard, trackball, or mouse. (to
home row, top of ball/mouse).
NOTE: In applications where input devices
(keyboard, trackball, or mouse) are used more
like machine controls (intermittent one finger
entry on the keyboard, intermittent short term
use of the mouse or trackball) than for standard
typing (continuous use of keyboard for entry of
long character strings, extended use of trackball
or mouse in graphical environment), it is
appropriate to use the height and reach locations
described in §9, Hand Control Location (seated
station).
maximum 760 mm (30 in.)
minimum 710 mm (28 in.)
10.2.2 Vertical leg clearance. minimum 673 mm (26.5 in.)
10.2.3 Horizontal leg clearance, depth at knee level. minimum 508 mm (20 in.)
10.2.4 Horizontal leg clearance, depth at foot level. minimum 660 mm (26 in.) depth ×
254 mm (10 in.) vertical foot
clearance