semi合集-English.pdf - 第6466页
SEMI G77-0699 © SE MI 1999 7 Symbol Value Specified Datum Measure d From Feature Me asured To y 5 200 mm maximu m facial dat um plane rear o utsid e edge of frame cassette includ ing rear cover y 9† 92.5 mm facial da tum…
SEMI G77-0699 © SEMI 1999 6
Table 1 Dimensions for Frame Cassette
Symbol Value Specified Datum Measured From Feature Measured To
θ‡
45 ± 0.5° either vertical datum plane sides of position and orientation notches
r13† 2.5 mm
2.6 minimum
line segment along center of
cassette sensing pad
edge of cassette sensing pad
x1 203.5 mm
maximum
bilateral datum plane outer surface of frame cassette (without
handles)
x2 240 mm
maximum
bilateral datum plane furthest reach of human handles
x3 177 mm
minimum
187 mm
maximum
bilateral datum plane inside edge of tape frame support
x4 191.5 ± 0.3 mm bilateral datum plane inside wall of frame cassette
x13† 88.5 mm bilateral datum plane
near end of line segment along center of
front cassette sensing pads
x14† 118.5 mm bilateral datum plane far end of line segment along center of
front cassette sensing pads
x17† 17.5 mm bilateral datum plane line segment along center of rear cassette
sensing pads
x41‡ 30 ± 1 mm bilateral datum plane front right orientation notch on robotic
handling flange
x42‡ 50 ± 1 mm bilateral datum plane front left orientation notch on robotic
handling flange
x43‡ 50 ± 1 mm bilateral datum plane rear orientation notch on robotic handling
flange
x44‡ 53 mm
maximum
bilateral datum plane encroachment of box underneath robotic
handling flange
x45‡ 65.3 ± 1 mm bilateral datum plane
nearest point of side position and
orientation notches on robotic handling
flange
x46‡ 71 ± 1 mm bilateral datum plane sides of robotic handling flange
x47‡ 58 mm
minimum
bilateral datum plane end of robotic handling flange front and
rear
x56‡ 194.75 ± 0.25 mm bilateral datum plane outside edge of bottom rails
x57 187 mm
maximum
bilateral datum plane box sides underneath bottom rails
y1 193 ± 0.25 mm facial datum plane front outside edge of frame cassette
y2 193 ± 0.25 mm facial datum plane back outside bottom edge of frame
cassette
SEMI G77-0699 © SEMI 19997
Symbol Value Specified Datum Measured From Feature Measured To
y5 200 mm
maximum
facial datum plane rear outside edge of frame cassette
including rear cover
y9† 92.5 mm facial datum plane
front end of line segment along center of
rear cassette sensing pads
y10† 123.5 mm facial datum plane
rear end of line segment along center of
rear cassette sensing pads
y18† 40.2 mm facial datum plane
near end of line segment along center of
front cassette sensing pads
y19† 61.1 mm facial datum plane
far end of line segment along center of
front cassette sensing pads
y41‡ 30 ± 1 mm facial datum plane
left orientation notch on robotic handling
flange
y44‡ 53 mm
maximum
facial datum plane
encroachment of frame cassette
underneath robotic handling flange
y45‡ 65.3 ± 1 mm facial datum plane nearest point of front and rear position and
orientation notches on robotic handling
flange
y46‡ 71 ± 1 mm facial datum plane front and rear edge of robotic handling
flange
y47‡ 58 mm
minimum
facial datum plane end of robotic handling flange sides
z1 183 mm
maximum
13-frame cassette
303 mm
maximum
25-frame cassette
facial datum plane top of frame cassette
z2† 2 mm
maximum
horizontal datum plane bottom of frame cassette sensing pads
z3 23 mm
maximum
horizontal datum plane internal floor of frame cassette
z4 33 mm horizontal datum plane bottom nominal film frame seating plane
z5 10 mm each nominal film frame seating
plane
adjacent nominal film frame seating
planes
z65 mm
minimum
bottom of film frame support top of film frame support below
z7 10 mm
minimum
top surface of the top frame
support
internal ceiling of frame cassette
z8 15 mm
minimum
horizontal datum plane top of x56 and y1 dimension controlled
area
z9 215 mm horizontal datum plane bottom nominal film frame seating plane
of top stacked cassette (13 slot only)
z12 0 ± 0.5 mm
each nominal tape frame seating
plane
bottom of the tape frame
SEMI G77-0699 © SEMI 1999 8
Symbol Value Specified Datum Measured From Feature Measured To
z41 1 mm
minimum
horizontal datum plane bottom of frame cassette
z43 1 + 0 -1 mm horizontal datum plane bottom rails
z47‡ 210 ± 1 mm
13-frame frame cassette
330 ± 1 mm
25-frame frame cassette
horizontal datum plane bottom of robotic handling flange
z48‡ 15 mm
minimum
bottom of robotic handling flange encroachment of frame cassette top
underneath robotic handling flange
z49‡ 8 mm
maximum
bottom of robotic handling flange top of robotic handling flange
† These dimensions match those of SEMI E1.9 with the same symbol.
‡ These dimensions match those of SEMI E47.1 with the same symbol.
NOTICE: These standards do not purport to address
safety issues, if any, associated with their use. It is the
responsibility of the user of these standards to establish
appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
SEMI makes no warranties or representations as to the
suitability of the standards set forth herein for any
particular application. The determination of the
suitability of the standard is solely the responsibility of
the user. Users are cautioned to refer to manufacturer’s
instructions, product labels, product data sheets, and
other relevant literature respecting any materials
mentioned herein. These standards are subject to
change without notice.
The user’s attention is called to the possibility that
compliance with this standard may require use of
copyrighted material or of an invention covered by
patent rights. By publication of this standard, SEMI
takes no position respecting the validity of any patent
rights or copyrights asserted in connection with any
item mentioned in this standard. Users of this standard
are expressly advised that determination of any such
patent rights or copyrights, and the risk of infringement
of such rights, are entirely their own responsibility.
Copyright by SEMI® (Semiconductor Equipment and Materials
International), 3081 Zanker Road, San Jose, CA 95134. Reproduction o
f
the contents in whole or in part is forbidden without express written
consent of SEMI.