semi合集-English.pdf - 第7880页

SEMI T13.1-1104 © SEMI 2004 4 RELATED INFORMATION 1 SECS MAPPING FOR RESTRICTED INFORMATION NOTICE : This related information i s not an official part of SEMI T13.1 and was derived from the Japanese Traceability Committe…

100%1 / 7923
SEMI T13.1-1104 © SEMI 2004 3
Parameter Name SECS-II Data Item Reference SECS-II Format Remarks
ServiceStatus L, 2
1. <SVCACK>
2. L, p
1. L, 2
1. <ERRCODE
1
>
2. <ERRTEXT
1
>
….. ….. …..
p. L, 2
1. <ERRCODE
p
>
2. <ERRTEXT
p
>
SVCACK = (10)
ERRCODE = (51, 52, 54)
ERRTEXT = (20)
If service was successful,
P = 0 and no error list is
attached.
If not, the maximum length
of each ERRTEXT must be
80.
Target L, 2
1. <SPNAME>
2. <SPVAL>
SPNAME = Target
SPVAL = (20)
TraceData L, 2
1. <SPNAME>
2. <SPVAL>
SPNAME = TraceData
SPVAL = (00, 1x, 2x, 3x, 4x, 5x)
“x” is an appropriate octal
defined in SEMI E5.
Tracer L, 2
1. <SPNAME>
2. <SPVAL>
SPNAME = Tracer
SPVAL = (20)
Tracers L, 2
1. <SPNAME>
2. <SPVAL>
SPNAME = Tracers
SPVAL = (20)
Item L, 2
1. <SPNAME>
2. <SPVAL>
PNAME = (20)
PVAL = (00, 20)
Name of Service <SVCNAME> 20 Note: message name other
than message parameter.
4.3 The Other Communication — The other SECS-II communication may additionally take place to run
manufacturing systems. Such communications as event report and exception notification are usually done from
equipment to host. Also some instructive communications for manufacturing as job management and remote
command are done from host to equipment. But they are just recommended to do regularly and independently to this
specification because they are not in the scope of traceability but in production scope.
SEMI T13.1-1104 © SEMI 2004 4
RELATED INFORMATION 1
SECS MAPPING FOR RESTRICTED INFORMATION
NOTICE: This related information is not an official part of SEMI T13.1 and was derived from the Japanese
Traceability Committee. This related information was approved for publication by full letter ballot on July 23,
2004.
R1-1 Particular Mapping for Specific Equipment
R1-1.1 Often some backend equipment may just handle such characteristic data of each device on a strip substrate
as sorting or classification data and transfer information. Characteristic information exchanging service messages
and their parameters are mapped as shown in the following tables. This mapping is one of possible specific
mappings for arrayed characteristic device information on a strip and there may not be a full mapping but just for
particular functions related to the exchanging services. This mapping is based on SEMI G84 with some extension.
Table R1-1 Service Instructions Mapping
Service Message Name Supporting Class Stream, Function SECS-II Message Name
showData DieTraceData S14, F1/F2 Get Attribute Request / Data.
ShowProperty DieTraceData S14, F1/F2 Get Attribute Request / Data.
takeDTD DieTracer S6, F11/F12 Selected Equipment Status Request / Data.
Table R1-2 Service Parameters Mapping
Parameter Name SECS-II Data Item Reference SECS-II Format Remarks
DataValue L, 2
1. <ATTRID>
2. <ATTRDATA>
ATTRID = (20)
ATTRDATA = (0, 1x, 2x,
3x, 4x, 5x)
showData of DieTraceData
(specific use for data content, or
whole characteristic map data on
a substrate including some
properties).
Designation <ATTRID> ATTRID = (20) showProperty of DieTraceData.
Property L, 2
1. <ATTRID>
2. <ATTRDATA>
ATTRID = (20)
ATTRDATA = (0, 1x, 2x,
3x, 4x, 5x)
showProperty of DieTraceData.
<ACKC6> ACKC6=(10) showData, showProperty. ServiceStatus
<OBJACK> OBJACK=(51) takeDTD of DieTracer.
TraceData <V> V=(0, 1x, 2x, 3x, 4x, 5x) takeDTD of DieTracer.
NOTICE: SEMI makes no warranties or representations as to the suitability of the standards set forth herein for any
particular application. The determination of the suitability of the standard is solely the responsibility of the user.
Users are cautioned to refer to manufacturer's instructions, product labels, product data sheets, and other relevant
literature, respecting any materials or equipment mentioned herein. These standards are subject to change without
notice.
By publication of this standard, Semiconductor Equipment and Materials International (SEMI) takes no position
respecting the validity of any patent rights or copyrights asserted in connection with any items mentioned in this
standard. Users of this standard are expressly advised that determination of any such patent rights or copyrights, and
the risk of infringement of such rights are entirely their own responsibility.
Copyright by SEMI® (Semiconductor Equipment and Materials
International), 3081 Zanker Road, San Jose, CA 95134. Reproduction of
the contents in whole or in part is forbidden without express written
consent of SEMI.
SEMI T13.2-1104 © SEMI 2004 1
SEMI T13.2-1104
SPECIFICATION FOR XML PROTOCOL FOR DEVICE TRACKING
This specification was technically approved by the Global Traceability Committee and is the direct
responsibility of the Japanese Traceability Committee. Current edition approved by the Japanese Regional
Standards Committee on July 23, 2004. Initially available at www.semi.org September 2004; to be published
November 2004.
1 Purpose
1.1 The purpose of this document is to map Services
and data in SEMI T13 into XML protocol.
2 Scope
2.1 This document is applied to XML implementation
of Jigs and Implements traceability with some
interoperability with Surface Mount Technology (SMT)
equipment.
NOTICE: This standard does not purport to address
safety issues, if any, associated with its use. It is the
responsibility of the users of this standard to establish
appropriate safety and health practices and determine
the applicability of regulatory or other limitations prior
to use.
3 Limitations
3.1 This protocol mapping has a consideration being
interoperable with SMT manufacturing it may be used
in such area, using this specification on such
manufacturing area is not guaranteed because this
specification is originally planned to be working on
semiconductor manufacturing systems including
equipment.
4 Referenced Standards
4.1 SEMI Standards
SEMI T12 — Specification for Tracing Jigs and
Implements
SEMI T13 — Specification of Device Tracking:
Concepts, Behavior and Services
4.2 Association Connecting Electronics Industries
(IPC)/National Electronics Manufacturing Initiative
(NEMI)/American National Standard institute (ANSI)
1
IPC-2501 — Definition for Web-Based Exchange of
XML data; (July, 2003)
IPC-2541 — Generic Requirements for Electronics
Manufacturing Shop-Floor Equipment Communication
1 http://www.ipc.org, http://www.nemi.org, http://www.ansi.org, The
original developer is IPC with NEMI cooperation, ANSI ends up with
authorizing approval.
(CAMX); (October, 2001 / ANSI Approved November,
2001)
4.3 World Wide Web Consortium (W3C)
2
REC-xml-20001006 — Extensible Markup Language
(XML) 1.0 (Second Edition)
NOTE-SOAP-20000508 — Simple Object Access
Protocol (SOAP) 1.1
4.4 Internet Engineering Task Force
3
RFC2045 — Multipurpose Internet Message
Extensions (MIME) Part 1: Format of Internet Message
Bodies
RFC2616 — Hyper Text Transfer Protocol – HTTP/1.1
NOTICE: Unless otherwise indicated, all documents
cited shall be the latest published versions.
5 Terminology
5.1 Abbreviations & Acronyms
5.1.1 MIME — Multipurpose Internet Message
Extensions
5.1.2 SOAP — Simple Object Access Protocol
5.1.3 XML — eXtensible Markup Language
6 Base Requirements
6.1 Base Protocol Mapping — This XML protocol
specification adopts Simple Object Access Protocol
(SOAP) over Hyper Text Transfer Protocol (HTTP) on
Transmission Control Protocol/Internet Protocol
(TCP/IP). Some equipment users produce not only
semiconductor devices but also Print Circuit Boards
(PCBs). It is convenient for such users to have common
messaging protocol with standard messaging for
Surface Mount Technology (SMT). For this purpose
this protocol mapping extension standard specifies the
messaging mechanism conformant to IPC-2501
“Definition for Web-Based Exchange of XML Data” as
2 World Wide Web Consortium, 32 Vassar St. Room 32-G515,
Cambridg, MA 02139, USA Telephone: 617.253.2613; Fax:
617.258.5999, http://www.w3c.org,
3 http://www.ietf.org, IETF Secretariat c/o
Corporation for National
Research Initiatives, 1895 Preston White Drive, Suite 100, Reston,
VA 20191-5434, USA, Telephone +1 703 620 8990, Fax +1 703 620
9071